Schematic CAT 950H / 962H Loaders and IT62H Toolcarrier Electrical System

Full Work Material - Learn

CATERPILLAR 950H/962H/IT62H LOADERS

ELECTRICAL SYSTEM

950H and 962H Wheel Loaders, IT62H Integrated Tool Carrier, Electrical System, Wire Description, Power Circuits, Bat, Head LMP, AIH Breaker, Lift Position Sensors, Engine ECM, Main Power Relay Output, Warning Horn (Forward), RH Dash Indicator Panel, Supplementary Steering, Auto Lube Pump to Payload Monitor, Beacon, Heated Mirror, Rotary Tilt Position Sensor, ECAP/Center Dash Indicator Panel, Engine ECM, Implement ECM, Transmission ECM, Unswitched Fuse Bus Power, Hood Actuator Breaker, Hood Actuator, Ground Circuits, Main Chassis, Operator Monitor Return, XMSN CTRL, Engine ECM, Rotary Tilt Position Sensor, Implement Return, Basic Machine Circuits, Start Relay to Starter Motor, Start Relay to Transmission ECM, Main Power Relay Coil, Backup Alarm Lamp Travel Alarm, Warning Horn (Forward), Hood Raise Motor, Hood Raise Motor, Hood Raise Relay Coil, Throttle Position, Monitoring Circuits, Supplemental Steering SW, Primary Steering SW, Parking Brake SW, Power Train Oil Filter, Air Filter, HYD System Temp Gage, Power Train Temp Gage, Fuel Level Gage, Supplemental Steering Fault Lamp, Primary Steering Lamp, Hydraulic Oil Filter, Front Brake Temperature, Rear Brake Temperature, Washer, Front, Lift Press Sensor, Lift Position Sensor, Lighting Circuits, Stop Lamp, Turn Lamp, Head Lamp Low, Fuel Priming Pump SW to Fuel Priming Pump, Control Circuits, Supplemental Steering Motor Relay, Supplemental Steering Control SW, Bucket Positioner Sol SW, Quick Coupler Engage Sol, Not Used, Start Aid Solenoid Return, Left Turbo Inlet Press, Start Aid Solenoid Drive From Engine ECM, Bucket Position SW, Park Brake Lever SW to GND, Implement Control Reversing Fan Sol, Implement Control Lift Proportional Sol, Implement Control Lower Proportional Sol, Implement Control Tilt Cylinder Position, Fan Control Sol Positive, Fan Control Sol Return, Throttle Sensor Common, Fuel Pressure SW, Axle Cooler Clutch, Axle Cooler Clutch, Boost Pressure Sensor Ground, Atmospheric Press Sensor, Front Guard Motor, Front Guard Motor, Engine ECM Pressure Sensor Return, Engine ECM Pressure Sensor Common, Inlet Air Heater, Transmission Clutch, Diverter Sol, ENG Throttle Control, Inlet Air Temperature, Fuel Filter Monitor, Trackback Proportional, Engine Speed, Engine Speed, Anti Drift Sol, Quick Coupler SW to Quick Coupler Solenoid, GND Level Shutdown, Component Location, AIH, Backup, Alternator, Arc Suppressor, Batteries, Breaker, Alternator, Belly Guard Actuator, Hood Actuator, Main, Running Lamp, Unswitched Bus, Engine, Autolube Pump, Front Washer, Fuel Priming Pump, Hood Actuator, Rear Washer, Secondary Steering, Secondary Steering Intermediate, Fuel Level, Atmospheric Pressure, Boost Pressure, Coolant Temperature, Front Axle Oil Temperature, Fuel Pressure, Hydraulic Oil Temperature, Lift Cylinder Head End Pressure, Lift Position, Oil Pressure, Schematic Location, Rail Pressure, Rotary Lift Position, Rotary Tilt Position, Transmission Input Speed, Transmission Oil Temperature, Turbo Inlet Pressure, Auto Reversing Fan, Axle Cooler Clutch, Lower Anti-drift, Raise Prop, Autolube Pressure, Belly Guard Actuator, Brake Oil Pressure, Bucket Position, Fork Position, Fuel Priming Pump, Ground Level Shutdown, Park Brake Pressure, Secondary Steering Pressure, Trans Filter Bypass, Engine Control System, Fuel Injector Solenoid, Injector Actuation Valve, Throttle Sensor...

• Pages: 1
• Size: 0.37 MB
• Format: PDF (Adobe Reader)

View Manual

WORK - CATERPILLAR - WHEEL LOADERS - INTEGRATED TOOLCARRIER - ELECTRICAL SYSTEM - WIRE - COMPONENTS - CONNECTOS - ENGINE CONTROL - FAILURE MODE - EVENT CODES - RESISTOR - SENDER - SOLENOID - SPECIFICATIONS - SYMBOLS